fbpx

Local Reviews
for Canal Winchester, OH


Shane C.

Shane C.

I Replaced the inducer motor cap & blower motor cap on this 2005 Bryant

Near Riding Trail Dr, Canal Winchester, OH 43110
Canal Winchester, OH - I  Replaced the inducer motor cap & blower motor cap on this 2005 Bryant
Shane C.

Shane C.

I am Performing our Five Star Tune-Up & Safety Check on a 2015 Bryant Gas Furnace. All readings were within manufacturer's specifications, unit operating properly at this time.

Near Riding Trail Dr, Canal Winchester, OH 43110
Canal Winchester, OH - 	I am Performing our Five Star Tune-Up & Safety Check on a 2015 Bryant Gas Furnace. All readings were within manufacturer's specifications, unit operating properly at this time.
Jacob M.

Jacob M.

The 1996 Bryant system ignition was lock out on arrival. I reset system and system fired up. I pulled and cleaned flame sensor

Near Braeswick Ct, Canal Winchester, OH 43110
Canal Winchester, OH - The 1996 Bryant system  ignition  was lock out on arrival. I reset system and system fired up. I pulled and cleaned flame sensor
Jacob M.

Jacob M.

I am Performing our Five Star Tune-Up & Safety Check on a 1999 Comfortmaker Gas Furnace. All readings were within manufacturer's specifications, unit operating properly at this time.

Near Alex Dr, Canal Winchester, OH 43110
Canal Winchester, OH - 	I am Performing our Five Star Tune-Up & Safety Check on a 1999 Comfortmaker  Gas Furnace. All readings were within manufacturer's specifications, unit operating properly at this time.
Jacob M.

Jacob M.

I was under the impression only a coupling needed added but during further inspection tech found trap 90 degree boot off plus 1/2” drain line had to be cut and coupling added and adjusted. I completely re-ran the ac/furnace condensate line

Near John Dr, Canal Winchester, OH 43110
Canal Winchester, OH - I was under the impression only a coupling needed added but during further inspection tech found trap 90 degree boot off plus 1/2” drain line had to be cut and coupling added and adjusted. I completely re-ran the ac/furnace condensate line
Jacob M.

Jacob M.

I found 1/2” 90 degree elbow disconnected from the 2012 Bryant furnace drain. I disconnected and re-routed pvc drain (AC line included). I has to return per short 1 pvc coupling but does have drain connected high enough for furnace, just ac evap is not connected so I instructed to not run ac until I returns

Near John Dr, Canal Winchester, OH 43110
Canal Winchester, OH - I found 1/2” 90 degree elbow disconnected from the  2012 Bryant furnace drain. I disconnected and re-routed pvc drain (AC line included). I has to return per short 1 pvc coupling but does have drain connected high enough for furnace, just ac evap is not connected so I instructed to not run ac until I returns
Jacob M.

Jacob M.

customer complaint, if they set tstat to 75 and the temp drops below 75 the tstat does not come on, on its own, they have to bump the tstat up a few degree to get it to come on. I could not get tstat to duplicate per I am unable to sit at home for a long amount of time to witness this. when called for heat system worked as supposed to. as of the check list system is operational/ heating with in manufacturing specifications at this tine

Near Quinlan Blvd, Canal Winchester, OH 43110
Canal Winchester, OH - customer complaint, if they set tstat to 75 and the temp drops below 75 the tstat does not come on, on its own, they have to bump the tstat up a few degree to get it to come on. I  could not get tstat to duplicate per I am unable to sit at home for a long amount of time to witness this. when called for heat system worked as supposed to. as of the check list system is operational/ heating with in manufacturing specifications at this tine
Jacob M.

Jacob M.

customer concerned if the 2004 Ruud Gas furnace is shutting off when supposed to. I explained from her statement that it sounds like a thermostat issue. I could not get issue to duplicate while in home. I suggests to replace tstat with simple non-programmable tstat. furnace operational/ heating with in manufacturing specifications at this time

Near Quinlan Blvd, Canal Winchester, OH 43110
Canal Winchester, OH - customer concerned if the 2004 Ruud Gas furnace is shutting off when supposed to. I explained from her statement that it sounds like a thermostat issue. I could not get issue to duplicate while in home. I suggests to replace tstat with simple non-programmable tstat. furnace operational/ heating with in manufacturing specifications at this time
Shane C.

Shane C.

I am Performing our Five Star Tune-Up & Safety Check on a 2013 Carrier Gas Furnace. All readings were within manufacturer's specifications, unit operating properly at this time.

Near Jennings Dr, Canal Winchester, OH 43110
Canal Winchester, OH - I am Performing our Five Star Tune-Up & Safety Check on a  2013 Carrier Gas Furnace.  All readings were within manufacturer's specifications, unit operating properly at this time.
Shane C.

Shane C.

I Found thermostat not set up properly for 2005 Concord heat pump . I configuration and a jumper wire jumped at heat pump between Y1 and O terminals preventing heat pumps reversing valve to energize and switch over keeping the condenser in cooling mode while running electric heat at the same time. Was able to get the heat pump to produce heat

Near Fence Row Ct, Canal Winchester, OH 43110
Canal Winchester, OH - I Found thermostat not set up properly for 2005 Concord heat pump . I configuration and a jumper wire jumped at heat pump between Y1 and O terminals preventing heat pumps reversing valve to energize and switch over keeping the condenser in cooling mode while running electric heat at the same time. Was able to get the heat pump to produce heat